FullDecalkit for Pontiac Firebird Trans 1978 Limited trunk scoopHood StripesSticker
Includes:
-1 X Large Firebird Hood Decal.
-2X Small firebird for A pillar.
-2 X Trans Am decal (left andright fender).
-1 X Trans Am decal for frond bumper.
-1 X Trans Am decal rear trunk.
-2 X T/A -66 for hood scoop.
-10 XMeters pin stripe for edges.
High grade Vinyl as Factory Spec (Polymeric).
Many Colors, please Add a note on your order or messages oneBay.
Available Colors are:Matte Black - Gloss black - White matte- White gloss - Gold - Silver - Black - Grey - Yellow - Forest Green - Red -Blue - light Blue - Orange - lime green.
INSTALATION INSTRACTIONS
Step 1:Clean the vehiclesurface thoroughly. Pay special attention to edges, and cracks that may behiding dust or grime.
Step 2:Test fit byholding your vinyl in place with masking tape. Mark position with tape, or tapein place along top edge, allowing you to peel the backing paper. Make sure thedecal is not backwards. Right side decals will only fit well on the right sideof the car and vice-versa for the left side
Step 3:Wet vehiclesurface with water solution (See general instructions above). Try to avoidgetting the backing paper wet. It would cause it to break down and make itharder to remove.
Step 4:Peel backing paperand generously spray adhesive side of vinyl with water solution.
Step 5:Make surepositioning is correct. (Water allows you to temporarily slide the vinyl aroundthe surface). Once you're happy with the position, move to the next step.
Step 6:If working with solid stripes, or unmasked vinyl,spray top of vinyl before you squeegee to avoid scratches. If in doubt, spraymore. It's good to work with lots of solution, even on your hands.
Step 7:Firmly squeegeevinyl in place, working from center out. If the vinyl moves at all while tryingto squeegee, spray more solution and carefully reposition. Be careful not tostretch the vinyl too much as it might deform.
Step 8:Spray masking / transfer tape to loosenand let sit for 5 minutes. This allows it to loosen enough and also give thevinyl time to stick better to the car's surface.
Step 9:Carefully peelback masking / transfer tape, keeping it flat with the surface so you don'tpeel up the fresh vinyl. If some of the vinyl peels off you can add solutionand slip back into place and squeegee again.
Step 10:Trim extra overlapalong edges with razor blade if needed. In more cases you won't need to trim,though some kits require it. Just be careful not to scratch the paint whentrimming. Most bubbles will squeegee out. However, some remaining bubbles canbe carefully popped with a needle or corner of your razor blade before pressingdown on it again.
Step 11:Park in the sun tohelp the stripes dry quicker. The hot sun will also help get rid of somebubbles. Allow a few days with the car in a sun before attempting to wash thevehicle. During this time, be gentle when you wipe down the car or the graphicsto avoid damaging them. After a few days you can begin to handle the car as younormally would.
PAYMENT POLICY
Accept PayPal.
We ship the items when the payment is clear.
SHIPPING POLICY
Free shipping worldwide.
Tracking number always provided within 24 hours.
Free international shipping takes 7-24 working days.
Tracking number can be track at the following link: track-trace.com/post
RETURNS POLICY
Returns Accepted (within 30 days after delivery).
Item must be return in its original condition for full refund.
Damaged products arerefunded by providing evidence (photos).
If item arrive damaged we are happy to send a free replacement(Please send a message before open case, we are happy to resolving issues withcustomers.
CONTACT& SUPPORT
Response within 24 hours.
We are happy to helpsolving any issue.
